PowerBox Systems

PowerBox Systems - PowerBox Mercury SR2

SKU: 358474

Category: PowerBox

Manufacturernumber: 4130
GTIN: 4250416704771

349,00 €

incl. 19% VAT , plus

Available immediately
nur 1 Stück lagernd!

Lieferzeit: 1-2 Werktage

piece

Available immediately
nur 1 Stück lagernd!

Lieferzeit: 1-2 Werktage

The PowerBox Mercury SR2 is the first choice when a small, powerful power supply with maximum functionality is required. All the features that are otherwise only built into the larger power supplies can be found in the compact PowerBox Mercury SR2: iGyro, servo matching, free channel assignment and even a door sequencer make the system complete!

The PowerBox Mercury SR2 provides 16 freely assignable outputs, all of which can be individually adjusted by servo matching in 5 points. For models with larger control surfaces, where 2 servos are acting on the same rudder, the unique automatch function can precisely match the two servos in a matter of seconds.

The built-in iGyro software requires an iGyroSAT as the sensor unit - allowing 3 aileron, 3 elevator and 3 rudder functions to be individually controlled and set. The setup wizard simplifies the setup of the gyro system and reduces the effort to a few minutes. During initial setup, the wizard collects information about the wing, tailplane shape, and any vector control that may be present. A complex model matrix then calculates in the background which servo is connected to which output and links the corresponding gyro function. In addition, a whole range of expert settings offer all the freedom to adapt the gyro system to the respective requirements.

Additionally, the GPSIII or the PBS-TAV (True-Airspeed-Vario) can be connected to the FastTrack input. This adjusts the gyro sensitivity to the airspeed. All GPS or TAV information is also available for telemetry in the transmitter!

The output voltage of the PowerBox Mercury SR2 is regulated and can be set to 6.0V or 7.8V. The power of the two voltage regulators is generously designed by the milled aluminum heat sink on the top and bottom and will easily cope with current-hungry servos in 3D machines.

The built-in door sequencer can control a landing gear and up to three doors. Using the setup wizard, the endpoints of the doors are taught in a matter of minutes. Three predefined modes cover the vast majority of landing gear sequences. Afterwards, you can manually adjust the timing of the sequence control as desired.

For PowerBox and Jeti pilots, the PowerBox Mercury SR2 is almost completely* controllable and adjustable from the transmitter! Telemetry for battery and receiver data is fully developed for all supported systems.

*except sequencer and setup wizard

Features:

16 outputs
powerful battery crossover with high continuous power
sunlight readable OLED display
bilingual menu navigation
consequent double design of power electronics
redundant electronic switch
Servo matching for all 16 outputs
Automatching function
Doorsequenzer mit Einstellassistent
latest iGyro technology integrated, with the iGyroSAT as gyro sensor
9 independent gyro outputs for: 3x aileron, 3x elevator, 3x rudder
two selectable output voltages: 6.0V or 7.8V
optional with GPS III for speed dependent gyro compensation
Telemetry data for PowerBox P²BUS, Futaba S.BUS2, Jeti Ex-BUS, Spektrum SRXL2, Multiplex M-Link, JR X-BUS and Graupner HoTT
Transmission of battery, receiver and GPS data
Almost complete operability from the transmitter for PowerBox and Jeti
adjustable servo frame rate: 12ms, 14ms, 16ms, 18ms
Suppression of servo reverse currents

Technical data:

Operating voltage: 4.0V - 9.0V
Power supply: 2S LiPo, 2S LiIon, 2S LiFePo, 5S NiCd/NiMH
Current consumption operation: 100mA
Current consumption standby: 30µA
Strombelastbarkeit: 2 x 20A (<30s)
Dropout voltage: 0.3V
Ausgangsspannung: 6.0V, 7.8V
Signal input: serial

Scope of delivery:

PowerBox Mercury SR2
OLED Display
SensorSwitch NG
2 patch cables
4 rubber grommets and brass sleeves
8 mounting screws
Instruction manual in German and English

Manual