Kavan - Swift S-1 Semiscale red ARF - 2400mm

Kavan

Kavan - Swift S-1 Semiscale red ARF - 2400mm

SKU: 361048

Category: electric glider

Manufacturers: Kavan
GTIN: 8596450044852
HAN: KAV02.8083

449,90 €

incl. 19% VAT , plus

Available immediately
nur 1 Stück lagernd!

Lieferzeit: 1-2 Werktage

piece

Available immediately
nur 1 Stück lagernd!

Lieferzeit: 1-2 Werktage

Description
Reviews

At the end of the 80s of the 20th century, the Polish company Margański & Mysłowski Zakłady Lotnicze realized that there was a gap in the market of aerobatic gliders - the good old all-wood model Kobuz 3 SZD-21-2b designed in the 50s was no longer sufficient. So, in 1991, designers Edward Margański and Jerzy Cisowski, with the assistance of Jerzy Makula (then a three-time world champion in glider acrobatics), developed the new Swift S-1 model, a modern all-composite aerobatic glider with an incredible roll speed (only 4 seconds), which also manages loads of +/-10 g. The reward came almost immediately - Jerzy Makula won his fourth FAI World Championship title in glider acrobatics in the same year! And now you can enjoy flying with the semiscale of this beautiful glider with a wingspan of 2400 mm, powered by a powerful brushless motor!

The fuselage of the model is made of the highly durable EPO foam (extruded polyolefin) with solid internal carbon fiber reinforcements. The brushless electric motor C3548-750 with a 11x8-inch folding propeller and a regulator KAVAN R-50SB with a powerful BEC stabilizer, which is necessary to power 4 powerful micro servos on board, is installed in the bow. The cabin cover is removable and is attached with a pin at the front and a magnet at the rear. In the bow you will find enough space for a drive battery and a receiver. The rudder and elevator servos are located in the fin, and the rudders are controlled by short straight linkages.

The model's wing, made of EPO foam, consists of two parts with carbon fiber strips, whose led-out parts also serve as wing connectors and fit into the duralumin housings in the fuselage. The wing halves are attached with a plastic screw. The ailerons across the span of the wing (reinforced with carbon fiber tubes) are independently controlled by two servos with short straight wire linkages.

The tailplane is also made of EPO foam with reinforcements of carbon fiber tubes. The tailplane is attached to the fuselage with two screws and is easy to assemble and disassemble.

The model is powered by the C3548-750 class brushless motor with the KAVAN R-50SB 50 A regulator.

For power supply, you will need a LiPo 4-cell pack with a capacity of 2200-2700 mAh and a minimum power rating of 30C. Choose a concrete type so that the correct center of gravity position is maintained as much as possible without further ballast.

For power supply you need a LiPo 4-cell pack with a capacity of 2200-2700 mAh and a minimum load of 30C. Choose a concrete type so that the correct center of gravity position is maintained as well as possible without further ballast.

To control the model, you can also use a 4-channel computer RC set without special functions - in the basic version, the ailerons are always connected to only one channel with a Y-cable. Of course, it is ideal to use at least a 6-channel computer RC set, which allows independent control of ailerons by two servos and a mix for the airbrake. In this case, both ailerons control upward. This is also possible with the affordable Radiolink AT9S, AT10II or Futaba T6K and T10J transmitters. In this case the Y-cable of the ailerons in the fuselage must be replaced by two single (15-30 cm) extension cables. In der Anleitung gibt es natürlich auch eine ausführliche Tabelle mit einer bewährten Standardeinstellung der Ruderausschläge (einschließlich Mixer), damit Sie Swift S-1 einfach zum Flug vorbereiten.

The ARF set includes: