Kavan

Kavan - GO-1013MG (0.13s/60°, 3.8kg.cm)

SKU: 374455

Manufacturernumber: KAV20.1013MG
GTIN: 8596450031661

21,90 €

incl. 19% VAT , plus

Available immediately
mehr als 10 lagernd!

Lieferzeit: 1-2 Werktage

piece

Available immediately
mehr als 10 lagernd!

Lieferzeit: 1-2 Werktage

Very powerful programmable digital picoservo with titanium gearing and double ball-bearing output shaft is designed for use in small RC airplane models, RC cars 1:14-1:24, helicopters of size 400-450 and similar. The servo is placed in a plastic housing with an aluminum radiator in the middle. This ensures perfect cooling even under high loads.
With the USB programmer/interface for GO servos and the PC operating program, you can program a wide range of servo parameters.

Programmable functions:

Deflection size: Used to set the maximum size of the servo deflections. The default setting is approx. 120° for the normal range of control pulse widths (900~2100 µs); approx. 180° for the maximum permissible range of control pulse widths (500~2500 µs)
Neutral position of the servo: Used to set the neutral position (center position) of the servo
Damping: Sets the characteristics of the servo behavior when it stops moving
Output power: Sets the output power of the servo. The higher the value is, the faster the servo is and the higher the force is - of course, the power consumption is also proportionally higher. Range: 39.2~100%
Sensitivity: Sets the sensitivity (insensitivity bandwidth) of the servo. The higher the value, the narrower the insensitivity bandwidth - the servo will only move if the change in control signal width is greater than the insensitivity bandwidth.
Range: Ultra High (extra high - insensitivity band approx. 1 µs) - High (high - approx. 2 µs) - Medium (medium - approx. 3 µs) - Low (low - approx. 4 µs) -Soft start: Switches the soft start function on/off. This function prevents the servo from moving abruptly to the operating position after connection to the power supply, thus reducing the risk of damage to its gearing.
Servo reverse: Reverses the servo deflections.
FUTABA SR mode: Only for use with channels of FUTABA RC sets operating in SR mode. Do not switch this option on if you are using a different setup of the FUTABA RC set or an RC set of a different brand.
SANWA SSR mode: Only for use with channels of SANWA RC sets that operate in SSR mode. Do not switch this option on if you are using a different setup of the RC set SANWA or an RC set of a different brand.
Fail-safe: If the receiver's control signal fails completely or the servo cannot recognize the signal correctly (e.g. due to interference), the servo can switch to one of three emergency modes:
- (a) Free: Fail-safe is switched off.
- (b) Hold position: The servo retains the position that corresponds to the last correctly received signal.
- (c) Transition to neutral position: The servo returns to the neutral position (pulse width 1500 µs).
Overload protection: Activates or deactivates the servo overload protection in three stages - as soon as the overload persists for a preset time (in seconds), the servo output power is limited to the corresponding preset value (in % of the maximum power).
Reset: Restores the factory settings of the connected servo.
Standard supply voltage 4.8-6.0 V (nominal voltage).
Output shaft with 25-tooth/4.94 mm square drive.

Technical data:

Servo size: Micro
Servo type: Digital
Programmable: Yes
Positioning force with 4.8V [kg/cm]: 3
Positioning force with 6.0V [kg/cm]: 3.8
Speed at 4.8V [s/60st.]: 0.15
Speed at 6.0V [s/60st.]: 0.12
Servo gearbox: Titanium
Ball bearing: 2x
High voltage: No
Power supply: 4.8 - 6 V
Length: 22.8mm
Width: 12mm
Height: 29.4mm
Weight: 15g
Designed for airplanes,helicopters,road cars,off-road vehicles,ships